Club cart motors

Club cart motors DEFAULT

Golf Cart Motors - Club Car Motors (Regen) - 170-505-0002-14 MPH - Same Torque as Stock - replaces 10277510-48 volt Golf Cart Motors

Club Car Motors : 170-505-0002 : 14 MPH - Same Torque as Stock (Golf Cart Motors)

Part # 170-505-0002 - Works on the following Club Car Regen/Sepex Models : REGEN 1, REGEN 2/PD Plus, IQ or Precedent - 8 HP - 14-22 mph @ 48v.

To Confirm That this Specific Motor is Best For Your Golf Cart Setup, Application, & Performance Requirements, Go To the D&D Motor Systems Choosing A Golf Cart Motor Tool. 

We are the actual electric golf cart motor manufacturer, D&D Motor Systems, Inc. We design and manufacture these golf cart motors in Syracuse, NY and distribute the Alltrax controller which is also Made In The USA. Just connect with us during business hours. Our Blue Golf Cart Motors are the last golf cart motors being made in the USA. ("If its NOT Blue, its NOT true Red White and Blue!!!")

DISCLAIMER - NO PRODUCT LIABILITY CAN BE PROVIDED OR ASSUMED UNTIL D&D MOTOR SYSTEMS HAS ALL THE INFORMATION WITH REGARDS TO YOUR VEHCILE SETUP, APPLICATION, AND PERFORMANCE REQUIREMENTS. CALL D&D MOTOR SYSTEMS INC AT 315-701-0635.

Made In the USA

Sours: https://www.amazon.com/Golf-Cart-Motors-170-505-0002-14-Torque/dp/B06XKGLH2W

Club Car Electric Motors and Parts

club-car-electric-motor-parts-golf-cart-dd.jpg

Club Car Electric Motor and Engine Parts

Replacement Electric Motor/Engine Parts for Club Car Golf Carts

Find all your motor upgrades and replacement parts for DS, Carryall, and Precedent golf cart models. We carry Sepex motors, IQ drive systems, and series setups for most vehicles. Find a torque, high speed, or stock replacement motor for your golf cart at great prices. Please contact our knowledgable staff for correct packages suited best for your application.

We stock a full line of Club Car golf cart motors. Whether you are trying to upgrade your existing motor, or replace a bad one; WE CARRY AN EXTENSIVE INVENTORY. Our replacement motors come with a manufacturers warranty and documantation for install. We carry a stock replacement motor for IQ, Series, and Powerdrive drive systems. Which fit DS, Carryall, Turf, and Precedent electric units.

Sours: https://www.golfcartking.com/club-car-parts/club-car-motors-electric/
  1. 2020 yz85 big wheel
  2. Bobcat replacement tracks
  3. Clear label sheets for printer

Designed by Plum Quick Motors for Club Car and EZ-GO DC Golf Carts, both Series and Sepex systems.

75,000 Bandit

Bandit Upgraded examples:

Bandit upgraded Club Car 48 volt IQ GE brand motor, black stock controller, speed around 22 – 24 mph (estimated) and 25+% increase in low end torque with all stock components and that annoying regen braking is disabled.

Bandit PH upgraded Club Car 48 volt IQ AMD brand motor for Excel controller (gray or white controllers) carts, speed around 26 – 28 mph (estimated) with all stock components and that annoying regen braking is disabled.

Bandit upgraded EZ-GO 36 volt PDS AMD brand motor, speed around 22 – 24 mph (estimated) and 25% increase in low end torque with all stock components and that annoying regen braking is disabled.

Bandit upgraded Club Car 48 volt GE brand series motor, speed around 18 – 20 mph (estimated) and 25+% increase in low end torque with all stock components.

Bandit upgraded EZ-GO 36 volt DCS AMD brand motor, speed around 22 -24 mph (estimated) and 25% increase in low end torque with all stock components.

The Legendary “ Purple motor with a handle “
If you wanna be Quick ……………….. it’s gotta be PLUM QUICK !

Don’t confuse PRICE with VALUE ….. PRICE is what you pay and VALUE is what you get!
Purple motors are upgraded stock or aftermarket motors that you, the customer ship to us for speed and torque performance upgrades.

We try our best to keep the Bandit upgrade time frame just as short as we possibly can. With that being said, it all depends on our daily work load and in most cases that’s generally 3 weeks once the motor is in our shop. However, in cases of extreme work load, the time frame could reach 4 weeks. We’ll call for credit card information once your motor is ready to ship back to you.

Note: Bandit upgrade on Club Car DC Series or Sepex 10 Spline female motor coupling only!

Note: Bandit upgrade on EZ-GO DC Series or Sepex 19 Spline female motor coupling only!

Note: We don’t upgrade the following golf cart motors due to being poorly designed and/or the availability of obsolete parts: Hitachi, Fairplay, Zone, Gem, ThinkRuff/Tuff, Star, Tomberlin, FSIP, Baldor, Bad Boy Buggies, Admiral, EMP, Commander; or any double End cap motor male spline or female coupler.

Note: Plum Quick Motors does not recommend running stock motors upgraded to The Bandit on stretch and/or hunting/off road carts. Plum Quick motors recommends a custom built motor for these type of applications.

Receive a custom bronze double sided Plum Quick Motors “Fastest Name In Golf” coin valued at $25.00 free with the purchase of a Bandit upgraded motor.

Also, with each and every Plum Quick Motor upgrade you’ll receive a custom Plum Quick decal, custom post card and our one year warranty information sheet.

The Bandit process starts with a complete motor tear down, clean and inspect all parts. Motor case is striped down to bare metal, field coils are tested and repaired if needed, field and brush studs are inspected and replaced ($35.00 extra for new stud) if necessary, motor case bolt threads ( rear end side bolt threads ) are inspected and chased with tap if needed, motor case bolt threads ( end cap for brush rigging ) are inspected and chased with tap if needed. We weld on our trademark handle and then we spray on the Bandit trademark gloss Purple paint. We then clean and brush the aluminum to a satin finish. The brush holder is inspected for cracks and or loose brush guides and repaired or replaced ($35.00 extra for new brush holder) if necessary. The brush springs are inspected and tested for the proper tension and replaced if necessary. The brushes are inspected for loose leads, cracks, length and replaced ($50.00 extra for new brushes) if necessary then seated to remove hard glazing to allow the proper seating to the commutator. The armature is inspected and tested for weak, lifted or bad com bars. The commutator is machined and or polished to insure the proper fit for brush to commutator for max surface contact performance. The motor coupler on the armature is inspected to make sure it doesn’t have excessive wear (we don’t replace motor couplers). The armature then is high speed balanced to insure a smooth acceleration, no vibration at high speeds and then a high quality bearing is installed. Now, we build the motor back up with every part inspected, tested, cleaned and painted. During this build up process is when we do our trademark 12 point performance upgrade enhancements to each and every motor and date code for warranty purpose. Each and every motor is run on our custom built dyno machines before it goes to the packaging room for decals and boxing.

As a result of the above mentioned Bandit upgrade process these motors are better than brand new condition and have a higher horse power rating to provide much more torque and speed while running all other stock components.

Note: All stock EZ-GO DCS and PDS motors, Club Car Regen I, Regen II, IQ and Excel motors that are upgraded to the Bandit retain stock field map setting.

Note: If an aftermarket motor is sent in to have the Bandit upgrade done on it and this motor is for a EZ-GO DCS and PDS, Club Car Regen I, Regen II, IQ or Excel then you’ll use the original manufacturer’s field map setting if you upgrade the controller.

We can do the Bandit upgrade on all Club Car and EZ-GO 36 volt and 48 volt, Series and Sepex DC brush motors, as well as any aftermarket motor for these carts.

Note: Customer has 30 days to make payment of upgraded motor after we have contacted the customer that their motor is ready to ship back to them and if payment has not been made after 30 days of notification motor can be sold by Plum Quick to cover the upgrade cost.

Note: If customer sends in a motor Plum Quick deems to be unrepairable and/or unsuitable for upgrade the customer has 30 days after notification to have the motor sent back at their expense or the motor can be recycled by Plum Quick.

Series 36 volt and 48 volt carts will have a large lever for forward and reverse and no Tow/Run switch. Also, the field windings will be large gauge wire with 8 turns or less in most cases.

Sepex 36 volt and 48 volt carts will have a push button rocker switch for forward and reverse and a Tow/Run switch. Also, the field windings will be small gauge wire with multiple turns.

 

Note: Sepex motors upgraded to the Bandit will lose the regen braking feature.

36 volt Series carts with only the Bandit upgrade and all other components stock should get around a 20% increase in both overall torque and speed.

Note: Two different type motors were made for 36 volt Series carts for both Club Car and EZ-GO carts. One would be the gray GE brand thin can housing and the other being the black AMD brand thick can housing of these two the black AMD brand is the preferred motor. The gray 36 volt GE brand motor is ONLY to be used with 36 volts, stock components and standard tire height. However, the black AMD brand motor may be used with 36 volts or 48 volts with stock or upgraded components such as a higher amp controller. The difference between the two is with the gray 36 volt GE thin can housing the motor is a lighter duty motor that will draw higher amps and can over heat under harsh conditions, while the black AMD thick can motor is a heavy duty motor that can handle more load and because of this the motor will draw less amps doing the same or more work.

 

 

 

 

 

48 volt Series carts with only the Bandit upgrade and all other components stock should get around a 25+% increase in both overall torque and speed.

36 volt EZ-GO Sepex carts ( DCS or PDS ) with only the Bandit upgrade and all other components stock should get around a 25% increase in both overall torque and speed.

Note: The DCS motor has no speed sensor ( no wire pig tail on brush end of the motor ) while the PDS has a speed sensor ( see below picture of a PDS motor and the speed sensor ). You can use a PDS motor on a DCS cart because no speed sensor is used on the DCS cart. However, you can not run a DCS motor on a PDS cart with stock controller because the controller is set up to read the speed sensor pulse.

48 volt Club Car Sepex carts ( Regen I, II, IQ ) with only the Bandit upgrade and all other components stock should get around a 25% increase in both overall torque and speed.

Note: All the Club Car DS models with Sepex ( IQ )systems will have a black controller and the standard Bandit IQ upgrade will work.

Note: Precedent models with Sepex systems can have the black IQ controller, gray or white Excel controller. We’ll need the first 4 digits in the cart ID number to determine which Bandit upgrade will perform best with your cart.

Please note: It is a must that you have a good quality battery pack. At Plum Quick Motors we only use the BEST and in our opinion Trojan batteries are the top of the line.

The six volt battery will have three water fill holes, check your batteries once a month to ensure proper fill level is 1/8″ covering the battery plates. Use distilled water and always charge your battery pack after every use. Never let your battery pack go over one month without charging when not in use.

The eight volt battery will have four water fill holes, check your batteries once a month to ensure proper fill level is 1/8″ covering the  battery plates. Use distilled water and always charge your battery pack after every use. Never let your battery pack go over one month without charging when not in use.

The twelve volt battery will have six water fill holes, check your batteries once a month to ensure proper fill level is 1/8″ covering the battery plates. Use distilled water and always charge your battery pack after every use. Never let your battery pack go over one month without charging when not in use.

Note: The absolute best way to check the quality of your battery pack is to do a running voltage drop test across the whole battery pack. To perform this test you can use a cheap $20.00 or less voltmeter.

You’ll hook the meter leads across the battery pack, RED goes to the Positive post and the BLACK will go to the Negative post. See the below charts for + and – locations depending on a 36 volt, 48 volt (6 – 8 volt batteries) or 48 volt (4 – 12 volt batteries).

Once you locate the + and – connections on the battery pack, zip tie or use clips to hold the meter leads in place. Now place the meter dial on DC volts on a low scale as to read the pack voltage. Drive the cart holding the meter, you’ll get a voltage drop at take off as the cart is under a torque load. The pack voltage will drop and at the same time the amps will rise this is normal, once you get to full speed on level ground the pack voltage should be back to full voltage (36 volts on a 36 volt cart and 48 volts on a 48 volt cart) or very close to it. If your voltage is much less than full pack voltage (one or two volts makes a HUGE difference), then you may have a weak or a bad cell in one or more of your batteries. Remember, the battery pack is only as strong as the weakest battery in the pack! You can repeat this same test on each battery to find the weak link in your battery pack. Never put a new battery in with used batteries as the pack will never balance out properly. If you have to replace a battery in a used pack, replace with a used like brand battery. If the battery pack is maxed out running the stock motor and you put in a Bandit upgraded motor you could get a larger voltage drop as the Bandit motor will be a higher horse power motor and call more power to achieve greater torque and speed. The lower the voltage is across the battery pack the higher the amp draw can be and cause an over heating issue with cables, controller, F&R switch and/or the motor. This is why I always stress to all my customers make sure you have a good quality battery pack. The battery pack is the heart of the golf cart and without a good quality battery pack you’re never going to get full potential out of any performance upgrades!

Make sure your brakes are not dragging, you should be able to push and pull your cart with the brakes released on flat terrain. Also, make sure your tires are properly inflated to 25 – 30 psi.

Note: Customer must send in a repairable motor. If we have a proper motor core in stock you can purchase one of our motor cores to have upgraded to the Bandit for $175.00 extra added to the Bandit upgrade of $275.00. You can call for availability 1-803-548-7205.

Club Car Identification Charts


Note: With Club Car you’ll need to make sure the throttle is in good working order. If your cart has a V-Glide make sure at full throttle that the wiper arm is making contact with the last copper contact in the housing, if not adjust the linkage to ensure 100% throttle at full pedal.

Club Car V-Glide

Note: If you have a Club Car with mcor throttle make sure the mcor is sending 100% throttle at full pedal. Club Car IQ carts have a port to read the settings with a hand held programmer.

EZ-GO identification charts:


Note: With certain EZ-GO carts (1994 – current) you’ll need to make sure your ITS is set properly to insure you receive 100% throttle at full pedal.

Note: We like to make sure the plugger rod sticks out around an 1/8″ to ensure 100% throttle.

To maximize performance replace rear end fluid with high grade synthetic motor oil.

Increasing torque to your Bandit upgraded 36 volt or 48 volt Series motor: If you have the AMD style thick can housing you can upgrade to a 500 amp controller. If you have the 36 volt GE style thin can housing I wouldn’t recommend using anything above stock components, however if you have the 48 volt GE style thin can housing you can use a higher amp controller. *Note: South Carolina residents add 8% for sales tax*

*600 amp Series controller for your brand golf cart* $675.00

alltrax sr controller

 

If you choose to upgrade your controller to 500 amps it’s a must that you upgrade the following:

*2 gauge wire set for your brand golf cart* $250.00

*Heavy duty 36 or 48 volt solenoid* and diode $180.00

Note: Solenoid MUST be mounted upright!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*Heavy Duty Forward and Reverse Switch* is required when installing a higher amp controller.

EZ-GO Heavy Duty Forward and Reverse Switch $180.00.

EZ-GO

Club Car Heavy Duty Forward and Reverse Switch. This switch is for 36 / 48 volt golf carts, difference being the number of micro switches. $180.00.

Club Car

Increasing torque and speed to your Bandit upgraded 36 volt or 48 volt Sepex motor: You can upgrade to the Alltrax XCT controller. You’ll need the year and model of your cart to help determine the correct throttle and field map settings.

*Alltrax XCT controller* $675.00

If you choose to upgrade your controller it’s a must that you upgrade the following:

*2 gauge wire set for your brand golf cart* $250.00

*Heavy duty 36 or 48 volt solenoid* and diode $180.00

Note: Solenoid MUST be mounted upright!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heavy duty forward and reverse switch is not required with Sepex carts.

Note: If your current motor isn’t running I would suggest performing a motor test before you ship it in for the Bandit upgrade as to not pay for shipping just to find out your motor is beyond repair.

Motor Test for Series Carts:
Use a floor jack under the rear end center section to lift the rear wheels off the ground. Make sure you can turn the wheels by hand. Mark and remove all four motor wires. Use the below diagram and a fully charged 12 volt car battery. Make the jumper wires using 6 gauge battery cables. Once you touch the motor leads to the battery you’ll get a small arch and the wheels should turn slow. It doesn’t matter which direction the wheels turn.

Motor test for Sepex carts:
Use a floor jack under the rear end center section to lift the rear wheels off the ground. Make sure you can turn the wheels by hand. Mark and remove all four motor wires (isolate the battery pack first as to not damage the controller). Use the below diagram and a fully charged 12 volt car battery. Make the jumper wires using 6 gauge battery cables. Once you touch the motor leads to the battery you’ll get a small arch and the wheels should turn slow. It doesn’t matter which direction the wheels turn.

Note: If you have a Sepex cart and you decide to send us the motor for the Bandit upgrade make sure to flip the Tow/Run switch to Tow and then isolate the battery pack (remove the + cable from battery and – cable from battery) per below diagrams depending on your cart. This will help prevent controller damage when removing and installing the motor.

Series and Sepex battery pack layouts below.

Note: How to send in your motor for the Bandit upgrade.

Box your motor up using a good quality cardboard box, add packing as to protect the motor studs from getting bent and help prevent the armature from coming out of the motor housing.

Be sure and put a note in with the motor and include the following:
Name, address, phone number and if the motor is from a Club Car IQ cart give us the first four digits in the cart ID number as this will let us know which Bandit upgrade will perform best with your cart.

We try our best to keep the Bandit upgrade time frame just as short as we possibly can. With that being said, it all depends on our daily work load and in most cases that’s generally 3 weeks once the motor is in our shop. However, in cases of extreme work load, the time frame could reach 4 weeks. We’ll call for credit card information once your motor is ready to ship back to you.

*275.00 Bandit upgrade*

Ship UPS or FedEx to:

Plum Quick Motors
10590 Tillman Steen Road
Fort Mill, SC 29707

Note: Installing your Bandit upgraded motor:

Don’t put a bumper into the Bandit motor coupler once you get it back from Plum Quick. The Bandit motor has been tested on a dyno machine and if it had a coupler bumper and/or needed a coupler bumper it was tested and determined at that point to use or not. As for installing the motor onto the rear end, wire brush the rear end output spline shaft, you can spray a light coat of white lithium grease and now slide the motor onto the rear spline shaft all the way until the motor housing bumps the rear end housing. Line up and tighten the motor bolts to secure the motor to the rear end housing.

Note: When connecting the motor cables back to the motor it is a MUST that you use two wrenches (one on the nut near the motor housing, so this nut will not turn and the second to tighten the nut that will hold the cable lug) as to not spin the motor stud during the tightening of the cable lug to the motor

Note: Motor rotation:
Once you put in your Bandit upgraded motor and it goes in forward with the switch in reverse or goes in reverse when the switch is in forward, simply switch out the S1 and S2 motor leads if it’s a series cart or if it’s a Sepex cart isolate the battery pack and switch out F1 and F2. Test drive the cart and everything should work fine. If you have issues then please give us a call @ 1-803-548-7205.

Note: High speed gears are not recommended for carts with the Bandit upgrade.

Note: Motor temperature is very important in the longevity of any motor. Plum Quick motors recommends that the customer monitors the motor temperature with an inexpensive Infrared Temperature Gun. Monitor the temperature on the painted motor case. Motor case temperature of 190 degrees F or lesss is best. Don’t operate the cart with motor temperature above 190 degrees F as this can and will break down the winding and armature shellac causing a direct ground. To perform this test you can use a cheap $20 or less Infrared Temperature Gun.

All motors are guaranteed against defects in materials and workmanship for a period of one year from date of purchase from Plum Quick. All motors returned are subject to manufactures inspection and customer pays for shipping both ways.

Excluded from warranty are motors damaged due to the following with NO exceptions!

  1. Stalling the armature (pedal depressed and wheels not turning).
  2. Operating the motor under LOW or HIGH voltage conditions (running the motor on LOW battery pack or adding additional voltage to the motor).
  3. Exceeding the R.P.M. limit of the motor (running FULL throttle going down steep hills, running motor with cart on jack stands and no load on the motor).
  4. Prolonged HIGH amp draw (towing, hauling heavy loads, climbing steep hills or inclines).
  5. Using HIGH speed gears (high amp draw).
  6. Running OVER 22″ tall tires with stock controller (high amp draw).
  7. No warranty on speed sensor or magnet for Sepex Motors.
Sours: https://plumquick.com/bandit-electric-motor-golf-cart/
How To Upgrade Your Golf Cart Motor - Install, Torque, and Speed Test

ELECTRIC MOTORS FOR CLUB CAR GOLF CARTS

Our Club Car Golf Cart Electric Motor and Motor Parts selection includes Round insulator with 5/16" hole. For Advanced motors for Club Car golf carts item 536; AMD 36-volt ([email protected] rpm) series motor. Internal 10 spline. Speeds up to 23 mph on 36-volt cars item 7123; AMD 48-volt, ([email protected] rpm) internal 10 spline series motor. Speeds up to 17 mph . For Club Car 48-volt DS item 3255; AMD 36-volt ([email protected] rpm), 48-volt ([email protected] rpm) series motor. Speeds up to 25 mph on 48-volt and 22 mph on 36-volt. Internal 10 spline For Club Car series item 7119; AMD 48-volt ([email protected] rpm) or 36-volt ([email protected] rpm) (the BEAST) series, high torque motor For Club Car series 1994-up item 7114; AMD 48 volt (3.3 [email protected] rpm) motor to replace the factory installed motor EJ8-4001A, EJ4-4001 Club Car IQ item 3258; Road Runner redesigned motor for speeds up to 24 mph Club Car IQ item 6585; AMD 48-volt (5.5-hp), 36-volt (3.5hp) motor for speed Cas up to 22 mph on 36-volt and 24 mph on 48-volt Club Car Series item 31036; AMD 36-volt ([email protected] rpm) or 48-volt ([email protected] rpm) series motor. Stock replacement. 10 spline. Can be used with stock controller. For Club Car 1990-up item 7175; AMD 48-volt ([email protected] rpm) speed and torque motor For Club Car DS, Precedent all years, #7107 or #7108 for 2000-08, 2010-11 DS, Precedent item 7144; AMD 48 volt (5 [email protected] rpm) motor for speeds up to 24 mph Club Car IQ item 3294; Commutator Bearing for 1984--up club Car Electric (OEM# 1011290) item 3851; Insulator kit. For Club Car electric 1994-up item 313; Inner Rear Axle Bearing 1984-1986 Club Car electric models with Fuji axles (OEM 1012685) item 3895; Motor bearing and magnet kit. Includes 1 bearing and 1 magnet Club Car DS 2006-2008.5 & Club Car electric 2004-up Precedent item 5951; 3 wire sensor with snap in plug. For Club Car electric 2004-up Precedent with GE Motor item 9451; MAGNET, STOCK, CC,IQ, ADVANCED MOTOR item 3299;Advanced DC motor terminal hardware kit. Club Car electric 2004-up Precedent item 8387; AMD electric motor speed sensor kit for Club Car IQ and i2 Excel electric 2004-up DS & Precedent item 8415; Speed sensor For Advanced motors for Club Car item 9390; Brush springs For Club Car electric 1980-84 item 4325; Motor brush spring. For Club Car electric 1984-up item 4309; Brush holder and springs. For Club Car electric 1984-93, 36-volt item 514; Brush set for GE motors,3 shunt, for 5BC49JB3071, 5BC48JB3080, 5BC48JB3084, D392, D398 item 7143; Motor brush set. 1-3/4"L x 5/8"W x 1/2"D. For Club Car electric pre 1980 item 502; Motor brush. 1-7/16"L x 5/8"W x 1/2"D. For Club Car electric pre 1986 item 509; Brush set. 1-7/16"L x 5/8"W x 1/2"D. For Club Car electric 1980-93, 36-volt item 512; Brush assembly for new style G.E. motor. Includes 2 each. For Club Car electric 1994-up 36 & 48-volt item 545; Brush set with hardware for Advanced motors Club Car item 540; Brush holder and springs. For Advanced motors for Club Car item 5558; Motor axle clip. Club Car electric 1984-94-1/2 item 8394; G.E. motor bumper For Club Car electric item 6765; Motor ring guide for G.E. motors. For Club Car electric 1994-99 36 & 48-volt item 5733; Input shaft seal. For Club Car Electric 1994-1999, 36 & 48-volt item 3923; Insulator kit. For Club Car electric 1984-93, 36-volt item 530. 

 


Sours: https://discountcartparts.com/

Motors club cart

.

How to test an ezgo txt electric motor

.

Similar news:

.



729 730 731 732 733